Electric Gates
Thorpe St Andrew
Looking for electric gate installation in Thorpe St Andrew? We work with a trusted fabricator covering the area and east Norwich — supplying and fitting swing gates, sliding gates, driveway automation and electric bollards.
A look at our work
Every gate we fit is made to measure for the property it goes on. Here is a small selection of recent installations — traditional and contemporary, swing and sliding.
How much room do you actually have?
Thorpe St Andrew runs along the Yare on the eastern edge of Norwich, and its housing spans a wide range — riverside villas on Yarmouth Road, interwar and postwar suburban streets behind them, and modern development further out. What a good deal of it shares is a driveway shorter than it looks.
The constraint people run into is that a gate must not swing outward over a road or footway, however quiet the street. So on a shallow driveway the options narrow to hanging the gate inward if there is genuinely the depth, fitting a sliding gate which travels parallel to the boundary and needs none, or using rising bollards which take no space in either direction.
The measurement that settles it is simple. A swing gate needs roughly one leaf width of clear depth beyond the boundary, so a four metre opening with two two-metre leaves needs about two metres before the gate reaches a parked car, a step or the house. It takes a minute with a tape measure and it is the single most useful thing to establish before enquiring.
Coverage area: Thorpe St Andrew and east Norwich
Electric gate types & services
Electric Swing Gates
The most popular residential choice. Two leaves hinged to piers, in composite, steel, aluminium or wrought iron.
Learn more →Electric Sliding Gates
Travels parallel to the boundary, so no swing clearance is needed. Suits shallow driveways and wide openings.
Learn more →Cantilever Gates
Slides with no ground track at all — nothing crossing the driveway to fill with grit or leaves.
Learn more →Driveway Automation
Full systems including video intercom, keypads, remote fobs, vehicle detection loops and app control.
Learn more →Automate Existing Gates
Already have gates? In many cases motors can be added without replacing them, subject to condition and weight.
Find out more →Electric Bollards
Automatic rising bollards for driveways and commercial entrances. Raised for security, lowered flush for a clear opening.
Learn more →Gate Repairs & Servicing
Motor faults, damaged panels, failed intercoms and annual servicing to keep the safety system compliant.
Learn more →How much do electric gates cost in Thorpe St Andrew?
Prices depend on gate size, material, type and automation spec. Groundwork matters too — ground conditions, cable runs and the state of any existing piers all move a job within these ranges.
Prices and minimum specifications vary by region and installer. Send a few photographs with your enquiry and your fabricator can give you a realistic figure before anyone arranges a visit.
Full cost guide →Frequently asked questions about electric gates in Thorpe St Andrew
How much depth does a swing gate need?
Roughly one leaf width plus clearance. A 4 metre opening means two 2 metre leaves, so about 2 metres of clear depth beyond the boundary before the gate reaches a parked car or the house. On a shallow suburban driveway that is usually the deciding factor.
My driveway is too short. What are the options?
A sliding gate travels parallel to the boundary and needs no depth at all, though it does need clear space to one side. Rising bollards take no space in any direction and sit flush with the ground when lowered. Both are worth considering where a swing gate will not fit.
Can the gate open outward onto the pavement?
No. A gate must not swing over a road or footway, which includes the pavement, however quiet the street. That rules out an outward-opening swing gate where there is insufficient depth to open inward.
Do you install electric gates throughout Thorpe St Andrew?
Yes — our fabricator covers Thorpe St Andrew along with Sprowston, Old Catton, Rackheath, Postwick, Brundall and into Norwich.
How quickly can I get a price?
Send your postcode, the width of your opening and two or three photographs of the entrance and your fabricator can usually give you a realistic figure within a day or two, without waiting for a site visit.
Worth reading first
Which gate type suits you
How much space each type needs, materials compared, and how the automation works.
Buyer’s guide →Whether you need consent
The one metre rule, listed buildings and conservation areas, explained plainly.
Planning guide →What safe looks like
BS EN 12453, force limitation and safety edges — and how to spot a quote that omits them.
Safety guide →What it will cost
Real price ranges by gate type, and the factors that move a job within them.
Cost guide →Send your postcode, the width of your opening and a few photographs using the form below and your local fabricator will come back to you directly.
Electric gate installers across Norfolk
We cover the whole county, from King’s Lynn and the fens through Norwich and its villages out to the north coast. These towns each have their own page, and the surrounding villages of each are covered too.
Elsewhere in England
Covered by our fabricators
Scotland
33 towns across the central belt, Fife and the Borders
Don’t see your town? Send us an enquiry — the surrounding villages of each are covered too, or see all areas we cover.